Jason Goodrow, otherwise recognized as \"the Goodboy,\" is a license is granted tattoo artist that shares his expertise with the world in his articles.

You are watching: How to make a power supply for a tattoo gun


\"*\"

How to examine Your straightforward Tattoo Machine

If you purchased a tattoo kit, that is always best to check your equipment out. You'd it is in surprised by what you might find.Check all the screws on her machine. Over time, vibration can cause those screws to loosen, which reasons faulty to run of the machine.You should have actually a gap of around a dime’s width in between the an equipment contact screw and front spring.Finally (and this is a preference if mine), before you set up, take part emery cloth and go end your call screw a few times. This removes the built-up carbon on the end of contact suggest and enables for better electrical contact.

\"*\"

This is the power supply version I am right now using. It functions as great as the 200 dollar p.s. And also saves me $120.


Which power Supply must You Use?

There are a ton of power offers to select from, yet every brand offers the same thing: a controlled flow of electricity from your product to her machine. This permits you come tattoo at a much steadier and speedier rate than if girlfriend did it there is no power. (Remember, the sewing needle and thread with India ink? Yeah, that is much faster than that.)


This I'm certain of: No matter which friend choose, it will certainly basically job-related like the remainder of the rather on the market. Every make and model will offer various physical features, yet its simple purpose is the same.


Do I require a digital display of voltage?

Some strength supplies execute not display screen the volts that are being outputted. If you have one that these—just a dial through numbers—don’t worry. It'll still work fine, however you will must make sure that come make sure it's collection up effectively (see below).

What execute I require to check to make sure the device is mechanically set up correctly?

Check...

for a dime-sized broad gap in between the an equipment contact screw and front spring.that the clip cord is associated snugly in its suitable slots.that the needle is put correctly right into the tattoo tube.

These determinants will make a large difference in the performance of her machine. When you have actually ensured the everything set up correctly, you’re all set for the next step.


\"*\"

\"*\"

Checklist for setup Up Your strength Supply

Turn your power supply (PS from here on out) ON.Make sure your foot pedal and also clip cord space plugged in the correct slots.Double-check the clip cord link to her machine: If every is in order, organize your maker in her tattooing hand and also push down on the foot pedal. If you don’t acquire the prompt buzz, this probably means that the voltage is no turned increase high enough. Progressively turn the dial till you obtain an even, uninterrupted buzz.While the maker is running, check visually to view how much the needle is coming the end from the end of the tube's tip. I prefer much longer strokes on my liner and shader. I do not choose to drag the pointer of the pipe onto the client’s skin and also blindly tattoo the line through a quick stroke collection liners. With a much longer stroke, you room in control of whatever the needle does. That takes a ton the practice and experience, however the payoff is amazing. So, if you are running a shorter stroke setup tattoo liner, climate you must have set your needles to hang end the pipe 1/16th of one inch. If you want longer, then her needle must be comes out about 1/8 of one inch, and also you hang your needles just around flush v the tube.Next, revolve your tattoo device towards girlfriend so the you view the front check out of her machine. You should be able to see the armature bar nipple that you put into the loop of her tattoo needle. It need to be relocating up and down an extremely quickly — so quickly, in fact, that you must not have the ability to make out the loop on the needle.While the device is running, your needle should be coming the end 1/8 come 3/16th of an inch. This is not lot of difference, you might think, however that tiny gap between the skin and tip that needle allows the tattooist come visibly watch the lines of the used stencil.

\"*\"

How to tune Your machine Without a Digital leader on Your strength Source

Looking at the armature bar nipple, functioning under very strong resource of fluorescent light, if the PS is offering a perfect circulation of electricity, friend will an alert that the armature bar nipple moves in a figure 8. Ns don’t understand the exact technical jargon, but basically you room tuning your an equipment by the fluorescent light as if it to be timing light.If you execute see that number 8 movement as the tattoo maker is running, then opportunities are the the maker is ready for tattooing with.
Under fluorescent lights, keep your tattoo maker running. If it to run perfectly, friend will check out an apparent figure 8 top top the armature nipple.


Another means to tune Without Digital display screen or Fluorescent Light

If you perform not have fluorescent lighting or a digital display on her PS, you will perform the final tuning the old-fashioned way.

Please first make certain that your devices is set up correctly. Once you are ready, save your foot pressed down on the foot pedal.Begin by transforming up your power supply dial until you listen the buzz of your machine. When you hear that buzz, pay attention to how your needle looks as it begins to relocate in the up and down motion. Girlfriend are now tuning the tattoo device by ear and eye. Your maker should run smoothly.If your strength supply is turn up too high, it will sound prefer a really angry hornet and also there will certainly be visible sparks flying off of your call screw and the front spring. If this happens, slowly turn the dial under on the strength supply until the sparks have subsided and the machine buzzes in a softer fashion.To test it, rub your thumb against the armature bar nipple together the maker is running. The tattoo machine will bog under a bit. But, as soon as you remove your thumb, it will instantly resume its stable buzzing noise. If the tattoo maker bogs down and also will no restart after pressing down top top the foot pedal, possibilities are a contact screw requirements to it is in buffed a bit or you need to readjust your power setup just a bit.Now because that the visual component of tuning: you are generally looking to examine that her needle is no flopping around. If you see the needle bouncing roughly in the tube, there could be a couple of reasons—you can need to add a rubber band, you may have actually inserted the needle in the tube wrong, or your power is turn up as well high. So adjust accordingly. Once it’s perfect, then it is time come tattoo.
This is the strength supply illustration an electrical current. Notification the digital display and the voltage my device is pulling.


What around Power provides With Digital Displays and Memory Settings?

Let’s talk really briefly about power supplies that have digital displays and also memory settings. I certainly prefer these species of PSs.

As a habit, i make sure that mine tattoo makers are tuned mechanically first. This works great because the PS ns use has actually memory settings developed in come remember i m sorry voltage is set for a specific type of tattoo machine (liner/shader). There are differences and also you will see what I average when you begin and become much more confident in your an abilities and knowledge.What I choose the most about the digital display PS is the you deserve to see just how much voltage you are using and also you can likewise tell if the capacitor is being faulty, due to the fact that the voltage will different than normal. Also, because that the lazy, you can visually set the strength settings.

Online Lessons and Tutorials for the beginning of the person Tattooist

That is the lesson because that the day. Remember, if you have any kind of questions or comments please write-up them below and I will certainly be happy to answer any questions you may have. Talk to you every soon!


Questions & Answers

Question: mine gun just clicks. There’s no buzz the just slowly taps up and also down. What would certainly be your ideas of what’s wrong?

Answer: spring adjustment sound like perhaps too much tension.

Question: ns am currently using the same exact power supply because that my tattoo arts that you claimed you were using. I never had actually a trouble until the various other day. I was in the center of a tattoo as soon as all the suddenly the voltage jumped all the method up to 19.99. When I make the efforts to move the dial, it one of two people wouldn't change or it would simply start going down and back up, and never stop. Just how do I solve it?

Answer: inspect to see if you have actually a puffy fuse, it might be as basic as that.


Question: What voltage have to I set my liner at because that tattoo shading?

Answer: For beginning out, i think your an equipment should run about 6.6 volts both liner and also shader.

Question: What does the foot pedal ~ above a tattoo device do?


Answer: her foot pedal is merely breaking the circuit so it runs strength to your machines.

Question: Is it normal that the strength voltage autumn a bit, or turbulent while hitting the pedal?

Answer: Unstable... An interpretation that it fluctuates when just holding the pedal? ns need more information, please.


Question: What can I use to do a tattoo gun spring device out of due to the fact that someone stole all my stuff other than a item of a gun?

Answer: Hardened steel, 20 mm gauge for front and earlier spring... Friend will have to cut it and file it or punch it.

Question: sometimes when I'm tattooing the octopus doesn't it seems ~ to be going in is this since of the angle I'm tattooing?

Answer: Perhaps however the 45-degree edge is what you are aiming because that as much as good ink flow.

Question: Why does mine coil an equipment sound like a dead battery no issue what voltage it is on?


Answer: A couple of things... Behind spring could be broken, friend are absent an o-ring for her front spring, can you provide me much more information?


Question: To examine if your tattoo machine is running too high, would figure 8 ~ above the armature nipple be additional apart? and if also slow, closer together?

Answer: Nope you have it backwards... If maker is running as well high figure 8 will be tighter... But additionally you may have your spring adjusted incorrectly.

Comments

Jason Goodrow (author) native Washington State on march 04, 2020:

You can obtain bbn it from the manufacturer an ext than likely

crazyjay756473055 top top February 25, 2020:

where have the right to i obtain a wireing diegram for strength suppley


Jason Goodrow (author) from Washington State ~ above November 08, 2019:

Jeremy i need much more information about your situation


Jeremy top top November 05, 2019:

The bolt the tightens the call screw keeps breaking

Jason Goodrow (author) indigenous Washington State on march 10, 2019:

Opinions permitted but the civilization of ages past marked their skin with all type of product made indigenous from assorted articles and also sorry friend it is no all around art it's around the definition in the true tradition of making her body exactly how you like not paying a smoe 100 bucksfor mine dad's surname that can with Indian squid needle and thread for less than five bucks...


Harley Thornton on April 30, 2018:

I use the Hurricane Hp2 power supply.

But my best issue and for the life that me ns can't figure it out.. How to store the squid in the guideline as i tattoo (having to dip right into the ink every couple of seconds) I understand that's not right.

And I usually use the nickel and dime trick


Dime because that line nickel because that shade/colour,

I collection the strength supply unit at 6.8 or 7.3V because that shading and packing and also generally 9.4V because that line work.

And simply a tip for friend beginners out there.


If you have actually the correct V set on your power supply and also your an equipment is tuned properly you shouldn't have much problem tattooing.

I'm no pro myself this is my fourth year in the tattoo industry yet I know a lot about it.

The just thing ns stress around is how to keep the squid in the tip? If anyone can offer me any type of pointers that'd be good thanks

Jason Goodrow (author) indigenous Washington State on September 02, 2017:

Sorry it took so lengthy to get back at ya, Rotary machines are something various all together to job-related with, I have seen other males work through em, but color seems to autumn out which tells me that takes practice, and also probably the ideal rotary set up... I don't have sufficient experience to happen on rightfully, however like noþeles make certain to work on miscellaneous or someone that wont mind if your is touch up work later.


Dave on august 09, 2017:

Hi finding your blog good , can you use rotary makers for shading or room they finest for lining I have actually a stigma , bizarre rotary maker but also have four dragon eagle coil makers too which would certainly you recommend to it is in the finest for begginers

Jason Goodrow (author) native Washington State ~ above July 17, 2015:

LOL my girlfriend each machine has its own certain sound... As with a car... As long as friend hear a hard buzz v no sound gaps in that buzz ... That would be ideally what your looking for. However the various other variables are... What is the feather stock... What is your stress on her spring set... Just how do you line leading through the needle or indigenous the tip? several variables to look at... But additionally check out the various other lessons since how that setup renders the difference.


Jason Goodrow (author) indigenous Washington State on July 07, 2015:

So ns am not sure what the ps15/ and ps17 stand for....but if your starting out ns would indicate buying a liner and also shading tattoo machine. If you can not decide native the magazine you have it may be far better to shop around on ebay... Or even amazon... Tattoo devices are a dime a dozen... Yet you don't want to acquisition the cheapest either. Expect this helps your cause.


Thanks because that the read

Jason G

Jason Goodrow (author) from Washington State on might 27, 2015:

Man it really sounds prefer a floor issue... Damaged wire (clip cord/foot pedal) If her handy v a voltmeter you can check electrical continually and also tell if your power supply is bad. You will need to keep your foot pedal plugged in and make sure you are pushing it as soon as using the voltmeter... Make sure that the clip cord the goes to your device is not plugged in because that will be wherein you will test v the voltmeter.... If that side tests good then switch the end foot pedal v where you tested through the voltmeter. If that side tests an excellent as well.. Climate you have actually a broken wire on the clip cord or over there is a ground concern on the tattoo machine.... Check your washers on the machine... Might be a an easy issue as that.


Hey thank for the solution so ok correctly I have a duel digital display power it is provided n usually run it around 7.4 i m really sorry I'm still discovering as ns go and constantly will be willing to learn an ext thank your for the help, for this reason I just tried to run a new gun to shot it the end n that won't also work, question now is so together I conect cords all reflects light up an excellent but as soon as clip prongs go in total the light won't show up ~ above the cord light spot weather ns switch indigenous liner spot link to shader spot link the light don't go on like it have to be however that only happens as soon as I conect gun an equipment to clip cord prongs cuz up until I conect weapons up to it all lights show an excellent on strength supply displays however conect a gun increase n the don't go however pedal irradiate still mirrors n power display screen still there only just the light for clip cord link goes off even as I push pedal to run gun if u know any kind of idea top top what could be wrong allow me recognize pls would be a big help I would hate to buy all brand-new gear n this ingredient was just something simple so pls permit me recognize if u got any kind of idea ~ above my problem mean while give thanks to you for the great feed


I would inspect to check out if girlfriend have any kind of carbon construct up on her post and also front spring... That has tendency to happen and it can cause your tattoo device not to run. It will certainly stick...or occasionally spark, or occasionally nada... So obtain a piece of emery cloth and clean your contact point (post) and also even hit the front feather if you watch carbon or also rust... IF you check out rust... Eliminate the spring its no good. That rare yet not therefore rare that a capacitor on her tattoo machine blew... You will recognize this though since it would have actually made a pretty great popping sound, and also probably a small light show. Exact same gig examine all point out that power goes through... Her cord end can be loose, or bad, exact same with your foot pedal. If friend think every point is in order then start in on the power supply...light come on yet do you have actually a voltage display? If so what do you generally run your power settings at... Permit me know if this helped... Many thanks for the read!


jsngoodrow

country cropped kanak on may 20, 2015:

Hey for this reason sorry simply wondering if my strength supply lights up n appears to operation fine yet none the my firearms wont operation at all on the n ive used them alot before n had actually them for a good while n did fairly a few tatts v um n there still quit new just haven't provided um in a couple of months, ns was simply wondering if u could help me the end n let me understand what could be the problem on that.... Ne methods hopefully who can aid thankyou -country cropped kanak


Jason Goodrow (author) native Washington State ~ above April 14, 2015:

Woo Hoo! well have fun finding out its pretty an excellent stuff.


Amber ~ above April 14, 2015:

Actually I simply fixed it! say thanks to you because that the quick replies and also for posting your very helpful lessons!!!

Jason Goodrow (author) from Washington State ~ above April 14, 2015:

Also check your behind spring because that too much tension... Simple thing to forget if your new to messing v your springs.

Amber ~ above April 13, 2015:

Yeah I've to be messing with the contact screw and also the front feather in order because that it to run. My machine won't operation if it's under 10...why is that?

Jason Goodrow (author) native Washington State on April 13, 2015:


Ahhh i see... For this reason maybe examine your former spring... Sounds like to much tension and it wont relax it until you mess approximately with the call screw. Trust me if your new to this you're gonna probably be prefer what the hell is he talk about, also what is your power ratio when your to run the tattoo maker on your strength supply... If it has actually a screen.


Amber ~ above April 13, 2015:

I'm sorry ns wasn't an extremely clear haha what I meant was the if ns take mine foot turn off the pedal and also press on the again the won't rotate on again i would have to do that whole call screw routine

Jason Goodrow (author) from Washington State top top April 13, 2015:


Hi over there Amber, so read through this lesson again, but I will tell you the you need to merely keep her foot pressed ~ above the pedal to save the machine running... This is simply so friend have regulate over as soon as the tattoo machine runs, or if you simply need to prevent in general to wipe your customer off. Please read through... I have lessons talking around how to collection your an equipment up from the an extremely beginning. Hope this helped!

Thanks because that the read!

Gman

Amber on April 13, 2015:

Hi, I want to understand why mine tattoo device shuts off after i take mine foot turn off the pedal? To do it revolve on again, I keep my foot top top the pedal and also I screw the call screw come the finish of the former spring till it clicks and also I screw it back to the center of the front spring and also it works fine again. What should I do to do my tattoo maker keep ~ above running???


Jason Goodrow (author) indigenous Washington State on march 21, 2015:

Bob please describe my various other lessons, there is a ton the in development on the specifically, pics included.

Thanks because that the read

Mike on October 17, 2014:

hey G-Man, good read, and also commend you because that helping out the newbies.

Jason Goodrow (author) from Washington State on September 20, 2014:

Send it ago if the fuse is no blown in the power supply... That might be every it is.

babyhatchet top top September 17, 2014:


I just acquired my maker and ns hook that up and also there is no power getting to the device I am not certain what come do

Jason Goodrow (author) native Washington State on September 09, 2014:

You might need to examine the capacitor the is top top the machine, it may be mistakenly soldered or faulty altogether... First thing though is examine with a voltmeter together you press down top top the foot pedal and see what the yes, really voltage is there is no the maker attached, this should tell you the your power Supply is great or bad.... Expect this helped!


Mike on September 09, 2014:

I just bought a new clip cord due to the fact that my an equipment was not getting any type of power yet its still not getting sufficient power to operation the device what else can it be?


Jason Goodrow (author) from Washington State on respectable 04, 2014:

Not certain what the electric variances are, however most tattoo shops will certainly run 110v because that their strength supplies. So first get me the variances and also tell me a few things.

What type of tattoo machine are girlfriend using

What is your power Supply set at

Are her springs changed correctly

As much as lining general preeminence for outlines is 7-8 liner bug pin or long taper which ever before you prefer and lining should run in ~ 6.7 volts

Also inspect the various other lessons I have posted her needle bar need to go in one way only probably that's it/ broken spring... Never know


So details is what I require please write-up if serious.

Thanks

naidy on august 04, 2014:

Hi ns bought a new kit from one of the website I'm from southern africa I have a little problem through shading an lining I'm not certain wat voltage shud I use wen shading an how plenty of needles shud I use an wen the end lining I likewise have a problem with ink not chatching I need to go over my outlines double in order to acquire it dark an please help

Johne581 top top July 16, 2014:

My brother recommended I might like this website. He provided to be completely right. This post truly made my day. You can not consider simply exactly how so lot time I had spent for this info! Thanks! dedcdacedeac


Jason Goodrow (author) indigenous Washington State ~ above April 09, 2014:

Your liner will have a shorter front spring and also a bit of a steeper pitch about 45 level angle or so and your shader will have a much longer front spring and also the pitch is more shallow, much more like 30 degrees... Hope this helps, additionally take a look in ~ my other lessons too many of an excellent information!!!


kaki hemam top top April 09, 2014:

How can we identify the exact same two maker as liner & shader..actually ns bought two devices so still confusing i.e which machine should be linear/which device should it is in shader..... Pliz help me out of this...

Jason Goodrow (author) native Washington State ~ above February 21, 2014:


Hope you have actually the receipt...

jonh top top January 08, 2014:

first of every i desire to give thanks to you for your help,

my respect come you....aw a beginner ns bought two tattoo machines one shader and also one liner. I had actually the impression the both shader and liner contact points angles had to be at one o'clock,am i wrong??? .... And one more thing that might seem silly, I'm from europe and I have specifically the very same power supply as yours, ii have to tattoo in very same volts together you? 6 -6.8 ?? save up the good work

Jason Goodrow (author) indigenous Washington State ~ above September 17, 2013:


Sounds prefer your spring anxiety is to firm... You might need to weaken that spring just a bit... Don't overdo the or you can break it! let me know if this help or need an ext information

Jason Goodrow (author) from Washington State top top September 15, 2013:

not certain exactly however it practically sounds prefer you space grounding out somewhere in her equipment... Faulty wire in the pedal, link ports for her pedal in the p.s. It'self... No to speak it might be a damaged spring... Over there are numerous variables... Also check yet maybe for some factor your ports are details for what is plugged into it.... Permit me know if this helps!

steven on September 15, 2013:

hey basically ive had my tattoo equipment for a couple of months and also ive never had any problems to run machines prior to today when i went to set up i plugged every little thing in perfect and also now every time i use pressure come the foot pedal mine volts seem to be slowing/going down im so confused regarding what is walking on so might you please aid me


thanks alot

steven

Jason Goodrow (author) from Washington State ~ above July 26, 2013:

When i hear who say practice file I am assuming skin. Girlfriend left out some vital components that will help maybe trouble shoot her problem. First.. Good your maker is tuned come what friend say but when running what was the voltage to run at, additionally man, your needles might be placed wrong... That is a an extremely common mistake, following is what shading style were you using? and also what form of shader ( rounds or magnums ), and then following again especially coming from a kit what kind of ink... These are your key concerns. Hope this helps!

Mark on July 25, 2013:

Hey, I have a question. Ns bought a collection not too lengthy ago, and also have started practicing on practice paper, and my bestfriend permit me do one ~ above him, however when i did the on skin, whatever was tuned correctly, top top my strength supply i used about 6.5 for Lining and 7 for Shading. The makers seemed to sound correct and also everything was to run smoothly. Yet when I started to carry out it ~ above his skin, I discovered it difficult to synopsis the contour line of his tribal item which take it multiple transforms to run over every line simply to make it continue to be in his skin. Afterwards, I started shading the in through black, and it take it going over each shape about 6 or 7 times just to make that stick in his skin. Now after ns was done, he took a shower the next day, and when he wiped it off, the shapes have actually spots that room not totally colored in, and the lines weren't completely there. What deserve to I do to make nice, solid one move lines? and also how can I shade better with just normal black, or any color for the matter?


Jason Goodrow (author) from Washington State on July 21, 2013:

Skin textures and how your device is collection up dictate this number. I don't have actually a details magic number due to the fact that many the tattooists use various machines and also different power supplies, in addition to different shading techniques, this does not encompass ink type, spring tension, what kind of contact suggest you are using (brass, copper, or steel). Once you have actually tuned your device though what ever before the voltage number is need to be consistent through the tattoo, keeping in psychic you must never it is in running over 7 volts uneven you room pushing a enormous group the magnums, and if girlfriend are simply beginning, you will want to remain away from those until you have plenty of experience with a selection of shading techniques. Hope this helped!

Jason Goodrow (author) from Washington State on march 27, 2013:

Most the this will count on the size of the rounds and also magnums, but ideally correct it must be continuous voltage the you run your devices at.

Begner on march 26, 2013:


I have actually this question.. Round shaders and also magnums operation at the same voltage? or different?

Jason Goodrow (author) from Washington State on in march 25, 2013:

Again if anyone is tuning your an equipment and your using an ext that 7 volts, I would certainly be very hesitant on utilizing the equipment. Most specialists will tell you the exact same thing i am. If you started off cheap climate you may have finished up through a bunch of equipment that does not work. That is rare yet I have seen that on numerous occasions. If it to be me i would simply start from the beginning, collection your machines up, as I suggest in the lessons, also check for that carbon develop up specifically after having actually run your tattoo device as girlfriend have. An excellent luck! save me posted.

Jason Goodrow (author) from Washington State on march 24, 2013:

There might be a couple of problems, and also its not always going come be power supply related. Every experienced tattooist ns have ever before met operation their equipments in the 6.0 - 6.8 range. If you space having problems with your an equipment not to run at these lower voltages climate it might be concerned the gauge of your spring, your call point, is the brass or metal? have actually you checked to make certain the contact allude has no carbon build up from to run at high voltage? likewise if it is a cheaper device it might only operation at those higher voltages but the high quality of the tattoo will certainly be hindered. There are countless things come pay attention too. Very first make sure that your contact points room at the ideal angles as I suggest in the mini lessons. Her liner will certainly be at one 'o' clock and also your shader will be at around three 'o' clock. Liner through a dime width gap and also your shader v a nickel broad gap. To trust me ns asked these very same questions and I even doubted the information. Most situations it no be your strength supply the is the trouble it will certainly be exactly how your machine is tuned. Expect this helped, please revisit those lessons they could have an ext to add. Thanks for reading!


Jason Goodrow (author) indigenous Washington State on January 25, 2013:

Hey over there edge Craog B basically had the same question as you, so monitor the instructions I provided him, see what I have the right to do for you guys.

Jason Goodrow (author) native Washington State on January 04, 2013:

Hi there Despina, if your prefer me and also can afford it, purchase a brand-new one. I have actually never encountered that trouble myself however a couple of things do come to mind. Sometimes, not frequently mind you, exactly how the electrical energy flows from the wall through the strength cable and also then the \"regulator\" that procedures down amount the will flow through the power supply itself, those deserve to go poor after years of use, and of course many things choose that space made in china since how cheap they are manufactured over there. One more thing is several of those P.S. Have actually fuses and also it may be prepared to pop. I have torn this specific p.s. Apart together well and also made comparison come the other ones ns use. If you are savvy, take it apart and check to make sure you have actually no crossed wires, sometimes things settle with age. Following question for you is exactly how long have actually you had this unit, since I had to bespeak a new cable for it, and also I have been using it for much better than 7 years. Right here is the adapter form I discovered for it, expect this helped.


model:ADS-24S-12-1224GPCU

INPUT:100-240V 50-60Hz

OUTPUT:12 V

Let me understand if this aided or not!

Jason Goodrow (author) native Washington State top top September 22, 2012:

There are several techniques you need to use to law smooth straight lines. A lot will start by the tube size you room using... I use a 1' tube grip this tends to provide me better control over line shakiness specifically with bent lines. Following thing with line work.... Acquire at the very least a three allude stretch, it will aid the ink enter the skin an ext smoothly as you work-related the tattoo, so there space a couple of tips that will certainly take treatment of a couple of things... A note though that takes time to build the stamin in her hand so heat up very first get a pen and put it in your an equipment and perform the stencil through hand you will certainly be pleased v the results, ns did it and if I have actually not tattooed ns do find a way to warm my tattoo hand up prior to going come work. Expect this helps.

Gman


Mario top top September 05, 2012:

Hi I have a question? ns would favor to currently if friend have any type of tips or means I can practice to do perfect directly lines. Ns not bad but on lack ho w over there is long lines I have have a hard time maintaining straight

Jason Goodrow (author) indigenous Washington State on respectable 14, 2012:

Cool, 8 does seem high to me together well. Try letting the maker run directly for a minute with no interuption. Then walk ahead and change down, store in mind it does not need to conveniently penetrate the skin favor the liner so by sound they space going to it is in different. Let me know

G-Man

sky on respectable 14, 2012:

hi, many thanks for the advice, it's in reality a shading machine that i can't it seems to be ~ to set up right, I've managed to obtain it to work-related without the sparks after ~ I discovered my ps to be broken and also got it replaced yet it only seems to work on a really high setting (around 8ish) whereas my liner functions at about 4, I'm obviously law something not correct I simply don't know what.

See more: Unexpected Token U In Json At Position 0 In Json, Unexpected Token U In Json At Position 0


Jason Goodrow (author) indigenous Washington State on respectable 12, 2012:

Hi there Sky... Therefore this sounds favor a maker set up issue. This may take a bit more to describe without some type of picture. So be patient. If this is a lining machine take a look at the angle or pitch of your call screw. My lining machines are collection up at around 2 o'clock so if the key is turn off this can reason problems... Also check that the contact screw is hitting close to the very edge of your front spring also if it is collection too far back same point will happen. These space a few things to take a peek at and like I claimed I have a device I have to replace a feather on for this reason I will certainly go ahead and also produce this lesson for everyone. Cave in there!!!

Jason Goodrow (author) from Washington State on august 12, 2012:

Hi Adam... Come answer a couple of of the concerns you posted. Your needle at full penetration should only enter the 3rd layer the the dermis, or in simple terms about an 1/8 inch. I have been tattoing a couple of years now and I like to work off my needle so that means I let the needles hang the end the end of the tube about a 1/16 of one inch, and then from over there I control the depth the needle is beginning the skin v a method I learned from an additional artist. So together your device is running it should look choose your needle is comes out virtually a 1/4 inch... This is an ext advanced technique... For begginers I suggest breaking out some type of melon or potato kind object and also practice on the a couple of times till you are able to work-related the ink right into it v out too countless problems. Keep me posted

sky on august 10, 2012:

hi, ns can't it seems ~ to one of my makers to job-related properly ns either obtain sparks or nothing, I'm a starting person so no sure just how to remedy this, please help

adambritsch on respectable 10, 2012:

i am just a beginner through tattoos and also i am no an artist or even looking to come to be one, im simply using mine gun top top myself and also figuring things out. I am a tiny confused about how deep the needle must be penetrating and how. It sounds choose the thumb rule is 'dime because that lines, nickel because that shade'. If that is correct, climate my concern is this; do you set the tip and also tube increase so that you deserve to drag the tip over the skin, or should have actually that 1/16\". It sound like even in your create up, girlfriend were hesitant to cite those depths especially for rookies. Thanks for the short article also, it was helpful. -Adam

Jason Goodrow (author) from Washington State on respectable 02, 2012:

So very first off lets not tattoo on anyone else until you have figured your devices out... That sounds like you basically put your devices together wrong and do not have actually your power settings correct. The needle snagging way not enough punch... Either feather is poor or power supply is not collection correctly. The tat scabbing and also then simply peeling off suggests spring issues again so start from scratch execute not tattoo everyone else till you have got this all figured out and also check the end my lessons on exactly how to acquire your tattoo an equipment set up simply in situation you let go something.

Keep me posted

Heather on august 02, 2012:

Just got a new kit and also it seems favor the needle snags, and then after ~ the tat scabs and peels off... It's no taking & no issue what that is snagging.. What can I execute or have to I be doing to settle this?